APPLICATION GUIDE

Metalworking Fluid Filter Bags

Filter bags remove swarf, fines and grinding sludge from metalworking fluids and coolants. Cleaner coolant lasts longer, protects pumps and nozzles, and gives a better surface finish.

Browse our filter bags

Metalworking fluids pick up metal chips, abrasive fines and sludge every time a machine cuts, grinds or erodes. Left in the sump, these particles wear tools and pumps, block coolant nozzles, mark finished surfaces and shorten the life of the fluid itself. A bag filter on the coolant return removes them continuously, with a quick bag change instead of a full sump clean-out. CLARIBag filter bags fit standard Size 1–4 bag filter housings and are stocked in our UK warehouse.

Understanding metalworking fluid filtration

Most machine shops use water-mixed fluids (soluble oil emulsions, semi-synthetics and synthetics) or neat cutting oils. Both carry three kinds of contamination: chips and swarf from cutting, fine metal and abrasive particles from grinding and finishing, and sludge that settles in the sump. Filtering the coolant as it returns to the sump keeps those solids from being pumped back to the cutting zone. Filter bags suit individual machines and small central systems, where a full filtration plant is not justified.

Applications of metalworking fluid filter bags

  • CNC machining and turning: removing chips and fines from coolant returning to the sump.
  • Grinding and honing: capturing fine abrasive and metal particles that spoil surface finish.
  • Wire and spark erosion (EDM): pre-filtering dielectric water or oil ahead of fine cartridges.
  • Parts washers and degreasing tanks: keeping wash solutions clean for longer.
  • Neat cutting and hydraulic oils: removing particles from oil returned to the tank.

Typical micron ratings

  • Swarf and chips: 100–200 micron nylon mesh, often as a first stage.
  • General machining coolant: 25–50 micron felt.
  • Grinding, honing and finishing: 5–10 micron felt.
  • Soluble oil emulsions: 10 micron felt or coarser, so the emulsion is not split.

On heavily contaminated sumps, use two stages, mesh then felt. The coarse bag takes the bulk of the swarf and the felt bag lasts much longer.

Problems addressed

  • Short coolant life: fines and sludge feed bacteria and break down the fluid.
  • Poor surface finish: recirculated particles score and mark workpieces.
  • Blocked nozzles and worn pumps: abrasive fines wear seals and impellers.
  • Frequent sump clean-outs: solids settle and need manual removal.

Recommended filter bag types

Nylon mesh filter bags (50–1000 micron)
Surface filtration for chips and swarf. Strong, with a precise opening size. Up to 80°C, or 120°C with a stainless steel ring.

Polypropylene felt filter bags (1–200 micron)
Depth filtration with high dirt-holding capacity for fines and sludge. Compatible with water-mixed fluids and most oils. Up to 80°C.

Polyester felt filter bags
For hot fluids up to 120°C.

Need a housing? See our bag filter housings.

Installation and best practice

Where to fit the filter
Fit the bag housing on the coolant return to the sump, or on a small pump loop that takes fluid from the sump and returns it clean. A pressure gauge either side of the housing shows when the bag is loaded.

When to change bags
Change the bag before the pressure difference across it reaches 1 bar, or at a set interval once you know your loading rate. Changing a bag takes minutes, compared with hours for a sump clean-out.

Disposal
Used bags hold metal fines and fluid residue. Dispose of them in line with your site's waste procedures for contaminated metalworking fluid.

Troubleshooting

Bags blocking quickly
Too fine a rating for the solids load. Add a mesh pre-filter stage, or move up one rating.

Coolant still dirty
Check that the bag collar seals properly in the housing; a poor seal lets fluid bypass the bag. Check that the rating is fine enough for the particles you are trying to remove.

Emulsion separating or concentration dropping
The felt may be too fine for a soluble-oil emulsion. Move to 10 micron or coarser.

Bag damage
Extremely sharp swarf can cut felt. Use a nylon mesh first stage.

FAQs

Felt or mesh for coolant?
Mesh for chips and swarf, felt for fines and sludge. Many shops use both, mesh first.

Will the bags fit my housing?
Universal W collar bags fit most standard Size 1–4 housings. For H-type collar housings, choose the Eaton/GAF replacement bags.

What is the minimum order?
5 bags of the same micron rating and size.

Can I set up a trade account?
Yes. Business customers can apply for a 30-day credit account.

Have a question about metalworking fluid filtration? Contact us.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.